7902 2RS MAX (Enduro) Frame Pivot Bearing
Note: Angular Contact Bearing
Inner x Outer x Depth (mm): 15 x 28 x 7mm
Used on: MTB Frame Suspension Pivots
Inner Diameter x Outer Diameter x Depth: 15 x 28 x 7mm
Used on: MTB Frame Suspension Pivots
Construction: Angular Contact - IMPORTANT, these bearings are directional and need to be fitted with black seal facing outwards. If not they will fail.
Precision Tolerance: ABEC3
Ball Roundness : Grade 10
Grease: High viscosity marine type grease
Note, This listing is for single bearings, and not pairs.
Angular Contact Bearings
The 7000 series bearings (i.e. 7902) are Angular Contact and thus can only be installed in one direction. These bearings will have different coloured seals on each side and are usually installed with the black seal facing you. Internally they contain an angled chamfer which will rely on a preload being applied (see the manufacturers instructions for your bicycle) which can result in the bearing falling apart if installled incorrectly. These bearings will enable vertical and horizontal forces to be spread evenly and thus will give extra strength and thus last longer.
Why Choose Enduro Bearings?
Unlike others, Enduro bearings are not just ‘off the shelf’ Industrial bearings. They are tailored specifically for the demands of cycling. Every aspect of an Enduro bearing is considered and spec’d to provide superior performance and value for each application. From the material of the races and the ball bearings, the types of seal and even the grease. Each of these has a profound effect of the performance and longevity of a bearing.
What is ABEC?
The ABEC grade of bearings is a set of standards for the manufacturing tolerances of bearings. There are five classes from largest to smallest tolerances: 1, 3, 5, 7, and 9. The higher ABEC classes provide better precision, efficiency and greater speed capabilities, but do not necessarily make the components spin faster. All quality manufacturers around the world manufacture to at least ABEC 1 standard. Enduro’s Minimum Standard is ABEC 3.
What is the meaning of Ball Grade?
Bearing balls are manufactured to a specific grade, which defines its geometric tolerances (or roundness). The smaller the number the higher the precision. A grade 20 ball for instance is 20/1,000,000" out of round. Enduro use Grade 10 for ABEC 3.
At Enduro they utilize several types of grease depending on the projected application of the bearing. They also fill both sides of the bearing for maximum lubrication, unlike industrial bearings which are only single filled. Wheel bearings (usually 2RS or LLB suffix) contain a low friction, temperature stable grease, whereas a Frame Pivot Bearings (MAX type) will contain a thicker waterproof marine type grease.
2RS: Literally means the bearing has Two Rubber Seals. There are many types of seals. On most other bearings 2RS means that the seal is made from rubber and has one sealing lip rubbing on any flat part of the inner race. Enduro’s seals are usually either LLU (usually the MAX type bearings) or LLB (better for hubs).
LLU Seals: Two NBR 70 rubber seals with medium/high contact seal, which rides in a matching groove machined into the bearing to make a labyrinth type seal. The outer sealing lip repels dirt and water while the inner sealing lip retains the grease.
LLB Seals: Two NBR 70 rubber seals with low contact seal, which rides in a matching groove machined into the bearing for low drag or friction.
Bearing Installation and Removal
Bearings should never be installed by pressing on the inner race. Always press on the outer race with a pilot bushing or similar tool, which will only make contact with the metal side of the outer race. A bearing press or similar should be used to exert the force needed to press the bearing into the housing. Ensure that the seating surface is clean and free from rough edges so that they fit true and square. Quite often bearings can feel fine before fitting, but then feel "notchy" or "rough" after fitting. This is almost always due to the bearings not sitting square and true. Care needs to be taken that the bearing is started straight and not at an angle to the housing.
To prolong the life of your bearings, do not direct a high jet of water near areas of your bike where there bearings are located - an ingress of water can lead to premature bearing failure.
CARD PAYMENTS - Note, extra security measures implemented by credit card issuers has resulted in card payments failing more frequently. If the billing address doesn't exactly match your registered card address you will not be able to proceed.
ROYAL MAIL - Please be warned we are seeing delays again from Royal Mail when you select our basic free Royal Mail 24 service (which isn't tracked). If your order is urgent, please select guaranteed next day service.